A STEP-BY-STEP GUIDE TO SETTING UP A TUB

A Step-by-Step Guide to Setting Up a Tub

A Step-by-Step Guide to Setting Up a Tub

Blog Article

Get A Free Estimate

On this page down the page you can get some good quality details around Tools You Need to Install a New Bathtub .


Tools You Need to Install a New Bathtub
Installing a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging task. If the old tub is easily easily accessible, the job can relocate quickly; if you need to open up a wall to remove the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to hiring a professional to take over a halfway-completed task, it is much better to think about using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This post will certainly aid you install a brand-new bathtub in your bathroom if you have already gotten a brand-new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your devices as well as product list need to consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining framework supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent stress on the tub.
    Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last setting.

    Removing Old Taps


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
    Before going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Mounting the Bathtub


    Making use of both wood boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
    The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
    To mount taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
    Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as likewise check the overflow outlet and the typical electrical outlet for leakages.
    Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the tub should wait until the tub has actually been made use of at least once as this will resolve it right into its last placement.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next off, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to permeate the wall in between the bath and the tiling, bring about issues with moisture and possible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealants to blend in your components and installations. They are sold in tubes and cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I'm very fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed the blog post. For those who enjoyed reading our article kindly do not forget to share it. Many thanks for taking the time to read it.




    Schedule Today!


    Report this page